使用tcping命令ping指定端口「建议收藏」

使用tcping命令ping指定端口「建议收藏」ping是简单的测试网络连接情况的小工具,对于一般用户很实用,但是ping有个缺点就是,不能指定端口,同时如果源地址禁ping的话,ping命令就形同虚设。——前言tcping命令是针对tcp监控的,也可以看到ping值,即使源地址禁ping也可以通过tcping来监控服务器网络状态,除了简单的ping之外,tcping最大的一个特点就是可以指定监控的端口。tcping命令使用方法很简单下载

大家好,又见面了,我是你们的朋友全栈君。

ping是简单的测试网络连接情况的小工具,对于一般用户很实用,但是ping有个缺点就是,不能指定端口,同时如果源地址禁ping的话,ping命令就形同虚设。——前言

tcping命令是针对tcp监控的,也可以看到ping值,即使源地址禁ping也可以通过tcping来监控服务器网络状态,除了简单的ping之外,tcping最大的一个特点就是可以指定监控的端口。
tcping命令使用方法很简单

  1. 下载tcping工具:http://www.elifulkerson.com/projects/tcping.php(分具体版本:32bit、64bit)
  2. 将下载的tcping.exe或者tcping64.exe文件放到C:\Windows\System32目录下(ping命令也是在这个目录下)
  3. 使用命令:tcping64 -d -t 127.0.0.1 6001

注意:如果你下载的是tcping.exe并且没有改文件名,在cmd中使用时需要输入tcping -p ip xxx使用,如果你下载的是64bit的tcping64.exe并且没有改文件名,在cmd中使用时需要输入tcping64 -p ip xxx使用

官方使用教程

NAME
    tcping - simulate "ping" over tcp by establishing a connection to network hosts.
    Measures the time for your system to [SYN], receive the target's [SYN][ACK] and send [ACK].  Note that the travel time for
    the last ACK is not included - only the time it takes to be put on the wire a the sending end.
SYNOPSIS
    tcping [-tdsvf46] [-i interval] [-n times] [-w interval] [-b n] [-r times][-j depth] [--tee filename] [-f] destination [port]
DESCRIPTION
    tcping measures the time it takes to perform a TCP 3-way handshake (SYN, SYN/ACK, ACK) between itself and a remote host.
    The travel time of the outgoing final ACK is not included, only the (minimal) amount of time it has taken to drop it on
    the wire at the near end.  This allows the travel time of the (SYN, SYN/ACK) to approximate the travel time of the
    ICMP (request, response) equivalent.
OPTIONS
    -4      Prefer using IPv4
    -6      Prefer using IPv6
    -t      ping continuously until stopped via control-c
    -n count
            send _count_ pings and then stop.  Default 4.
    -i interval
            Wait _interval_ seconds between pings.  Default 1.  Decimals permitted.
    -w interval
            Wait _interval_ seconds for a response.  Default 2.  Decimals permitted.
    -d      include date and time on every output line
    -f      Force sending at least one byte in addition to making the connection.
    -g count
            Give up after _count_ failed pings.
    -b type
            Enable audible beeps.
            '-b 1' will beep "on down".  If a host was up, but now its not, beep.
            '-b 2' will beep "on up".  If a host was down, but now its up, beep.
            '-b 3' will beep "on change".  If a host was one way, but now its the other, beep.
            '-b 4' will beep "always".
    -c      only show output on a changed state
    -r count
            Every _count_ pings, we will perform a new DNS lookup for the host in case it changed.
    -s      Exit immediately upon a success. 
    -v      Print version and exit.
    -S source_address
            Use _source_address_ as the tcp client's source address.  Must be a valid IP address on the client system.

    -j      Calculate jitter.  Jitter is defined as the difference between the last response time and the historical average.
    -js depth
            Calculate jitter, as with -j but with an optional _depth_ argument specified. If _depth_ is specified tcping will
            use the prior _depth_ values to calculate a rolling average.
    --tee _filename_
            Duplicate output to the _filename_ specified.  Windows can still not be depended upon to have a useful command line 
            environment. Don't tease me, *nix guys.   
    --file
            Treat the "destination" option as a filename.  That file becomes a source of destinations, looped through on a
            line by line basis.  Some options don't work in this mode and statistics will not be kept.
    destination
            A DNS name, an IP address, or (in "http" mode) a URL.
            Do not specify the protocol ("http://") in "http" mode.  Also do not specify server port via ":port" syntax.
            For instance:   "tcping http://www.elifulkerson.com:8080/index.html" would fail
            Use the style:  "tcping www.elifulkerson.com/index.html 8080" instead.                       
    port
            A numeric TCP port, 1-65535.  If not specified, defaults to 80.
    --header
            include a header with the command line arguments and timestamp.  Header is implied if using --tee.
    --block
            use a "blocking" socket to connect.  This prevents -w from working, uses the default timeout of around 20 seconds,
            and might break other expected behavior.  However, it can detect an actively refused connection vs a timeout.   
HTTP MODE OPTIONS   
    -h      Use "http" mode.  In http mode we will attempt to GET the specified document and return additional values including
            the document's size, http response code, kbit/s.
    -u      In "http" mode, include the target URL on each output line.
    --post Use POST instead of GET in http mode.
    --head Use HEAD instead of GET in http mode.
    --get Shorthand to invoke "http" mode for consistency's sake.
    --proxy-server _proxyserver_
            Connect to _proxyserver_ to request the url rather than the server indicated in the url itself.
    --proxy-port _port_
            Specify the numeric TCP port of the proxy server.  Defaults to 3128.
    --proxy-credentials username:password
            Specify a username:password pair which is sent as a 'Proxy-Authorization: Basic' header.
RETURN VALUE
    tcping returns 0 if all pings are successful, 1 if zero pings are successful and 2 for mixed outcome.
BUGS/REQUESTS
    Please report bugs and feature requests to the author via contact information on http://www.elifulkerson.com
AVAILABILITY
    tcping is available at http://www.elifulkerson.com/projects/tcping.php

常用的命令:

-4/-6 (优先使用IPv4/IPv6地址) -d (发送命令的时间) -t (-t是让命令持续运行,知道使用ctrl + c指令退出) -h (使用http模式) -u (与-h命令连用,输出目标的url) -n (发送命令的次数,默认4次) -i (发送命令的间隔时间,默认1s,可以为小数) -w ( 等待响应的间隔时间,默认2s,可以为小数)

实际应用

C:\Users\zhangyd>tcping64 -d -h -u -n 10 -i 0.1 -w 0.1 xxx.xx.xxx.xx 6001
** Pinging continuously.  Press control-c to stop **
** Requesting  from xxx.xx.xxx.xx:
(for various reasons, kbit/s is an approximation)
2016:12:06 10:36:07 Probing xxx.xx.xxx.xx:6001/tcp - HTTP is open - time=204.694ms page:http://xxx.xx.xxx.xx rcv_time=203.528 status=200 bytes=583 kbit/s=~22.916
2016:12:06 10:36:07 Probing xxx.xx.xxx.xx:6001/tcp - HTTP is open - time=208.675ms page:http://xxx.xx.xxx.xx rcv_time=208.560 status=200 bytes=583 kbit/s=~22.363
2016:12:06 10:36:08 Probing xxx.xx.xxx.xx:6001/tcp - HTTP is open - time=246.553ms page:http://xxx.xx.xxx.xx rcv_time=1040.546 status=200 bytes=583 kbit/s=~4.482
2016:12:06 10:36:09 Probing xxx.xx.xxx.xx:6001/tcp - HTTP is open - time=181.520ms page:http://xxx.xx.xxx.xx rcv_time=183.293 status=200 bytes=583 kbit/s=~25.446
2016:12:06 10:36:09 Probing xxx.xx.xxx.xx:6001/tcp - HTTP is open - time=195.658ms page:http://xxx.xx.xxx.xx rcv_time=202.854 status=200 bytes=583 kbit/s=~22.992
2016:12:06 10:36:10 Probing xxx.xx.xxx.xx:6001/tcp - HTTP is open - time=181.833ms page:http://xxx.xx.xxx.xx rcv_time=186.513 status=200 bytes=583 kbit/s=~25.006
2016:12:06 10:36:10 Probing xxx.xx.xxx.xx:6001/tcp - HTTP is open - time=227.706ms page:http://xxx.xx.xxx.xx rcv_time=226.750 status=200 bytes=583 kbit/s=~20.569
2016:12:06 10:36:11 Probing xxx.xx.xxx.xx:6001/tcp - HTTP is open - time=247.957ms page:http://xxx.xx.xxx.xx rcv_time=263.903 status=200 bytes=583 kbit/s=~17.673
2016:12:06 10:36:11 Probing xxx.xx.xxx.xx:6001/tcp - HTTP is open - time=235.967ms page:http://xxx.xx.xxx.xx rcv_time=187.247 status=200 bytes=583 kbit/s=~24.908
2016:12:06 10:36:11 Probing xxx.xx.xxx.xx:6001/tcp - HTTP is open - time=257.262ms page:http://xxx.xx.xxx.xx rcv_time=264.820 status=200 bytes=583 kbit/s=~17.612
Ping statistics for xxx.xx.xxx.xx:6001
     10 probes sent.
     10 successful, 0 failed.
Approximate trip times in milli-seconds:
     Minimum = 181.520ms, Maximum = 257.262ms, Average = 218.782ms
Approximate download times in milli-seconds:
     Minimum = 183.293ms, Maximum = 1040.546ms, Average = 296.801ms

上面命令的意思解释为:
使用http模式(-h)并且在返回数据中显示目标源url地址(-u)的方式向 ip为xxx.xx.xxx.xx 端口为6001的服务器发送10次数据包(-n 10),并且在返回数据行中显示发送数据包的日期(-d),指定每次发送数据包的间隔时间为0.1秒(-i 0.1)等待数据包相应的时间间隔为0.1秒(-w 0.1)

注:-t和-n同时存在时,优先指定-n,就是说:tcping64 -t -n 10 xxx.xx.xxx.xx命令只会发送10次数据包,并不是-t的持续发送

版权声明:本文内容由互联网用户自发贡献,该文观点仅代表作者本人。本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如发现本站有涉嫌侵权/违法违规的内容, 请发送邮件至 举报,一经查实,本站将立刻删除。

发布者:全栈程序员-用户IM,转载请注明出处:https://javaforall.cn/152518.html原文链接:https://javaforall.cn

【正版授权,激活自己账号】: Jetbrains全家桶Ide使用,1年售后保障,每天仅需1毛

【官方授权 正版激活】: 官方授权 正版激活 支持Jetbrains家族下所有IDE 使用个人JB账号...

(0)


相关推荐

  • VC编程来操纵Office[通俗易懂]

    VC编程来操纵Office[通俗易懂]使用VC编程来操纵Office。你可以实现诸如:Word文件打印、传送数据到Word文档、发送E-MAIL、自动产生表格、Excel数据统计、圆饼图,直方图显示、自动报表生成、播放幻灯、doc,txt,HTML,rtf文件转换、中文简繁体转换、拼音或笔画排序……只要是Office能够实现的功能,都可以在你写的程序中调用。仔细阅读下面的说明,并下载源文件进行参考,你就可以一步一步地掌握这个技

  • 详细图解什么叫平方探查法即二次探测再散列和线性探测再散列(数据结构 哈希函数 哈希冲突)

    详细图解什么叫平方探查法即二次探测再散列和线性探测再散列(数据结构 哈希函数 哈希冲突)虽然上文有提到怎么解释的开放地址法处理hash冲突,但是当时只是给了个简单的图,没有详细讲解一下,我当时有点不明白,回头查查资料,然后亲自动手,整理了一下。然后我就三幅图详细讲解一下:什么叫线性探测再散列;什么叫平方探测再散列(二次探测再散列);老师的ppt吧。给个原始数据如上图。下面详细解析。上面的是线性探测再散列。这个简单。

  • 一阶系统又称为惯性系统_舵机惯性控制

    一阶系统又称为惯性系统_舵机惯性控制1.PID.py#PID控制一阶惯性系统测试程序#*****************************************************************##增量式PID系统##**************************************

  • pycharm设置项目路径_vscode和pycharm区别

    pycharm设置项目路径_vscode和pycharm区别#-*-coding=utf-8-*-#@Time:${DATE}${TIME}#@Author:Donvink${USER}#@Site:${SITE}#@File:${NAME}.py#@Software:${PRODUCT_NAME}

  • Percona Data Recovery Tool 单表恢复

    Percona Data Recovery Tool 单表恢复Percona Data Recovery Tool 单表恢复

  • awk命令详解+示例

    awk命令详解+示例WK数据过滤工具(类似于grep,比grep强大)Awk编程语言/数据处理引擎创造者:Aho、Weinberger、Kernighan基于模式匹配检查输入文本,逐行处理并输出通常用在Shell脚本中,获取指定的数据,单独使用时,可对文本数据做统计#whichawk#rpm-qf/bin/awk语法格式:格式1:前置命令|awk[选项]‘条…

发表回复

您的电子邮箱地址不会被公开。

关注全栈程序员社区公众号