Controlling Broadcasts and Multicasts

Controlling Broadcasts and Multicasts为什么80%的码农都做不了架构师?>>>…

大家好,又见面了,我是你们的朋友全栈君。

Introduction

The first step in controlling broadcast and multicast traffic is to identify which devices are involved in a broadcast or multicast storm. The following protocols can send broadcast or multicast packets:

  • Address Resolution Protocol (ARP)
  • Open Shortest Path First (OSPF)
  • IP Routing Information Protocol Version 1 (RIP1)
  • Service Advertising Protocol (SAP)
  • IPX Routing Information Protocol (RIP)
  • NetWare Link Services Protocol (NLSP)
  • AppleTalk Address Resolution Protocol (AARP)

After identifying the source of the broadcast or multicast storm, you must examine the packets to find out which protocol or application triggered the broadcast or multicast storm. For example, if a single device is responsible for a broadcast storm, you can examine the device’s broadcast traffic to determine exactly what the device was doing. For example, you can find out what the device was looking for or what the device was announcing.

Broadcast or multicast storms are often caused by a fault that occurs during the device discovery process. For example, if an IPX-based printing environment has been misconfigured, a print driver client may continually send SAP packets to locate a specific print server. Unanswered broadcast or multicast requests usually indicate that a device is missing or has been misconfigured.

Examine the broadcast traffic on your company’s network. Do you see numerous unanswered, repeat queries? Do you see protocols (such as IP RIP1, SAP, and IPX RIP) that just “blab” all day even when no other devices may be listening?

Or, is the majority of the broadcast and multicast traffic on your company’s network purposeful? That is, does the broadcast and multicast traffic have a request-reply communication pattern? For example, are broadcast lookups answered?

Do broadcast packets contain meaningful information? For example, if a network has numerous routers, do broadcast packets contain routing update information?

Is the broadcast rate acceptable? Does your company’s network need RIP updates every 30 seconds, or can you increase the interval to one minute?

BROADCAST/MULTICAST DOMAINS

If your company’s network is experiencing excessive broadcast or multicast traffic, you should also check the scope of the broadcast or multicast domain. (A broadcast or multicast domain is the range of devices that are affected by a broadcast or a multicast packet.) Understanding broadcast and multicast domains can help you determine how harmful a broadcast storm can be from any point on the network.

The scope of a broadcast and multicast domain depends, to some degree, on the network design. For example, the picture below shows two networks, a switched network and a routed network:

control-b-u

On a switched network, Device 1 sends a broadcast or multicast packet that is propagated to all ports of the switch. (A typical layer-2 switch does not filter either broadcast or multicast traffic.)

On a routed network, however, a router does not forward broadcast traffic. If Device 1 sends a broadcast packet, only Device 2 and the router see the broadcast packet. If appropriate, the router processes the broadcast packet and sends a reply. Because the broadcast packet is not forwarded, it does not affect Devices 3 or 4.

转载于:https://my.oschina.net/qihh/blog/61060

版权声明:本文内容由互联网用户自发贡献,该文观点仅代表作者本人。本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如发现本站有涉嫌侵权/违法违规的内容, 请发送邮件至 举报,一经查实,本站将立刻删除。

发布者:全栈程序员-用户IM,转载请注明出处:https://javaforall.cn/149146.html原文链接:https://javaforall.cn

【正版授权,激活自己账号】: Jetbrains全家桶Ide使用,1年售后保障,每天仅需1毛

【官方授权 正版激活】: 官方授权 正版激活 支持Jetbrains家族下所有IDE 使用个人JB账号...

(0)


相关推荐

  • 暗影骑士擎bios详解_runloop原理和机制

    暗影骑士擎bios详解_runloop原理和机制Runloop什么是Runloop?从字面上讲就是运行循环。它内部就是do-while循环,在这个循环内部不断地处理各种任务。一个线程对应一个RunLoop,主线程的RunLoop默认已经启动,子线程的RunLoop得手动启动(调用run方法)RunLoop只能选择一个Mode启动,如果当前Mode中没有任何Source(Sources0、Sources1)、Timer,那么就直接退

    2022年10月28日
  • 英文斜体复制_斜体英文转换器,斜体英文26个字母可复制

    英文斜体复制_斜体英文转换器,斜体英文26个字母可复制斜体英文在网上用得越来越多,《复仇者联盟4》上映时,很多人在微博上都看到过它里面的经典台词:????????????????????????????????,????????????????????????????????????????????????????????????????????????.还可能看到过:?????????????????????????????????????????????????????????????????????????????????????

  • LabVIEW灰度图像操作与运算(基础篇—2)[通俗易懂]

    LabVIEW灰度图像操作与运算(基础篇—2)[通俗易懂]图像操作、像素操作以及图像运算等前期的图像操作不仅会在空间域增强图像,还能极大地提高后续图像处理算法的执行速度及其有效性。

  • unity3D入门_3D技巧

    unity3D入门_3D技巧unity3D入门系列一,Hello3DWorld(C#脚本版)作者:admin 日期:2011年06月25日 来源:本站原创  【字体:大 中 小】  我要评论(0) 文章转载自:http://www.j2megame.com/html/xwzx/ty/2275.html=======================================

  • tomcat日志乱码问题、页面乱码问题等

    tomcat日志乱码问题、页面乱码问题等一、默认解决方法无论Google还是百度,多数解决方法是server.xml设置URIEncoding=“UTF-8”。<Connectorport=”8080″protocol=”HTTP/1.1″connectionTimeout=”20000″redirectPort=”8443″URIEncoding=”UTF-8″/>二、接口乱码在catalina.bat头部增加-Dfile.encoding=UTF-8/bin/catalina.bat

  • CollectionUtils.isNotEmpty()的使用

    CollectionUtils.isNotEmpty()的使用List<Object>arrayList=newArrayList<Object>();当arrayList的数据为NULL时,可以用CollectionUtils.isNotEmpty()来判断arrayList是否有值CollectionUtils.isNotEmpty()包含null,size=0等多种情况CollectionUtils.isEm…

发表回复

您的电子邮箱地址不会被公开。

关注全栈程序员社区公众号