/******************************************************************************** * I.MX6 AW-NB177NF WIFI 驱动移植问题 * 说明： * 之前驱动移植，但看不到有wlan设备产生，于是感觉是wifi驱动出了问题，于是开始 * 分析厂家提供的wifi驱动，发现id对应的信息不对，经过与FAE确认之后并验证，确实是 * 这个问题导致的。 * * 2016-6-20 深圳 南山平山村 曾剑锋 *******************************************************************************/ 一、参考文档： 1. AW-NB177NF-DS-BC-Rev0.3_single Ant.pdf 2. 基于linux-2.6.38.8内核的SDIO/wifi驱动分析(转) http://www.cnblogs.com/hoys/archive/2013/01/09/2853715.html 二、wifi 驱动注册设备驱动的id相关代码： ...... static const struct sdio_device_id sdio_ids[] = { #ifdef CONFIG_RTL8723B { SDIO_DEVICE(0x024c, 0xB723),.driver_data = RTL8723B}, #endif #ifdef CONFIG_RTL8188E { SDIO_DEVICE(0x024c, 0x8179),.driver_data = RTL8188E}, #endif //CONFIG_RTL8188E #ifdef CONFIG_RTL8821A { SDIO_DEVICE(0x024c, 0x8821),.driver_data = RTL8821}, #endif //CONFIG_RTL8821A #ifdef CONFIG_RTL8192E { SDIO_DEVICE(0x024c, 0x818B),.driver_data = RTL8192E}, #endif //CONFIG_RTL8192E #if defined(RTW_ENABLE_WIFI_CONTROL_FUNC) /* temporarily add this to accept all sdio wlan id */ { SDIO_DEVICE_CLASS(SDIO_CLASS_WLAN) }, #endif { /* end: all zeroes */ }, }; ...... #define SDIO_DEVICE(vend,dev) \ .class = SDIO_ANY_ID, \ .vendor = (vend), .device = (dev) ...... #define SDIO_ANY_ID (~0) ...... 三、获取SDIO设备信息代码位置如下： static int sdio_init_func(struct mmc_card *card, unsigned int fn) { int ret; struct sdio_func *func; BUG_ON(fn > SDIO_MAX_FUNCS); func = sdio_alloc_func(card); if (IS_ERR(func)) return PTR_ERR(func); func->num = fn; if (!(card->quirks & MMC_QUIRK_NONSTD_SDIO)) { ret = sdio_read_fbr(func); if (ret) goto fail; ret = sdio_read_func_cis(func); if (ret) goto fail; } else { func->vendor = func->card->cis.vendor; func->device = func->card->cis.device; func->max_blksize = func->card->cis.blksize; } card->sdio_func[fn - 1] = func; printk("check sdio, func->vendor: 0x%x, func->device: 0x%x, func->max_blksize: 0x%x.\n", func->vendor, func->device, func- >max_blksize); return 0; fail: /* * It is okay to remove the function here even though we hold * the host lock as we haven't registered the device yet. */ sdio_remove_func(func); return ret; } 四、SDIO驱动获取到的信息： func->vendor: 0x24c, func->device: 0x626, func->max_blksize: 0x200. 五、解决办法： { SDIO_DEVICE(0x024c, 0x626),.driver_data = RTL8723B}, 六、查看结果： root@android:/ # busybox ifconfig -a can0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 NOARP MTU:16 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:142 can1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 NOARP MTU:16 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:143 ip6tnl0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 NOARP MTU:1452 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4683 errors:0 dropped:0 overruns:0 frame:0 TX packets:4683 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:703477 (686.9 KiB) TX bytes:703477 (686.9 KiB) sit0 Link encap:IPv6-in-IPv4 NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) tunl0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-10-00-00-00-00-00-00-00-00-00 NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 80:A5:89:49:6E:81 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@android:/ # 七、Linux kernel log: RTL871X: module init start RTL871X: rtl8723bs v4.3.16_13854.20150410_BTCOEX20150119-5844 RTL871X: build time: Jun 20 2016 09:05:58 RTL871X: rtl8723bs BT-Coex version = BTCOEX20150119-5844 RTL871X: module init ret=0 ...... check sdio, func->vendor: 0x24c, func->device: 0x626, func->max_blksize: 0x200. mmc2: new high speed SDIO card at address 0001 ...... RTL871X: register rtw_netdev_ops to netdev_ops RTL871X: rtw_hal_config_rftype RF_Type is 3 TotalTxPath is 1 RTL871X: Chip Version Info: CHIP_8723B_Normal_Chip_TSMC_B_CUT_1T1R_RomVer(0) RTL871X: EEPROM type is E-FUSE RTL871X: SetHwReg8723B: bMacPwrCtrlOn=1 RTL871X: PowerOnCheck: val_mix:0x0000063f, res:0x0000063f RTL871X: PowerOnCheck: 0x100 the result of cmd52 and cmd53 is the same. RTL871X: PowerOnCheck: 0x1B8 test Pass. RTL871X: _ReadAdapterInfo8723BS, 0x4e=0xe2 RTL871X: hal_EfuseSwitchToBank: Efuse switch bank to 0 RTL871X: hal_ReadEFuse_WiFi: data end at address=0xad RTL871X: Efuse Realmap: 08 28 00 62 07 0D 45 10 02 00 00 29 29 29 29 28 28 2F 2F 2F 2E 2E E0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 2D 2D 2D 2D 2D 2D 2D 2D 2D 2D 2D E0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 20 2C 20 00 00 00 FF FF FF 29 20 11 00 00 00 FF 00 FF 12 FF FF FF FF FF 3E 10 01 02 23 00 00 FF 20 04 4C 02 26 06 21 02 0C 00 22 04 00 08 00 32 FF 21 02 0C 00 22 2A 01 01 00 00 00 00 00 00 00 00 00 00 00 02 00 FF FF 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 EB 00 6E 01 00 00 00 00 FF 80 A5 89 49 6E 81 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF RTL871X: Hal_EfuseParseBTCoexistInfo_8723B: Enable BT-coex, ant_num=1 RTL871X: Hal_EfuseParsePackageType_8723B phy efuse read 0x1FB =fc RTL871X: PackageType = 0x4 RTL871X: Hal_EfuseParseVoltage_8723B hwinfo[EEPROM_Voltage_ADDR_8723B] =62 EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null) RTL871X: Hal_EfuseParseVoltage_8723B pHalData->adjuseVoltageVal =6 RTL871X: AutoloadFail =0, RTL871X: pHalData->EEPROMRFGainVal=f0 RTL871X: EEPRORFGainOffset = 0x29 RTL871X: SetHwReg8723B: bMacPwrCtrlOn=0 RTL871X: <==== _ReadAdapterInfo8723BS in 300 ms RTL871X: Hal_ChannelPlanToRegulation ChannelPlan:0x20,Regulation(2_4G/5G):0x03,0x03 RTL871X: init_channel_set ChannelPlan ID 20 Chan num:13 EXT4-fs (mmcblk0p4): warning: checktime reached, running e2fsck is recommended RTL871X: rtw_alloc_macid(eth%d) if1, hwaddr:ff:ff:ff:ff:ff:ff macid:1 RTL871X: rtw_register_early_suspend RTL871X: Init_ODM_ComInfo_8723b(): fab_ver=0 cut_ver=0 RTL871X: rtw_macaddr_cfg mac addr:80:a5:89:49:6e:81 RTL871X: bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0 RTL871X: rtw_ndev_init(wlan0) RTL871X: _rtw_drv_register_netdev, MAC Address (if1) = 80:a5:89:49:6e:81 ...... 八、Linux 命令行打开wifi： root@android:/ # netcfg lo UP 127.0.0.1/8 0x00000049 00:00:00:00:00:00 can0 DOWN 0.0.0.0/0 0x00000080 00:00:00:00:00:00 can1 DOWN 0.0.0.0/0 0x00000080 00:00:00:00:00:00 tunl0 DOWN 0.0.0.0/0 0x00000080 00:00:00:00:00:00 sit0 DOWN 0.0.0.0/0 0x00000080 00:00:00:00:00:00 ip6tnl0 DOWN 0.0.0.0/0 0x00000080 00:00:00:00:00:00 wlan0 DOWN 0.0.0.0/0 0x00001002 80:a5:89:49:6e:81 root@android:/ # busybox ifconfig wlan0 up RTL871X: +871x_drv - drv_open, bup=0 RTL871X: FW does not exist before power on!! RTL871X: SetHwReg8723B: bMacPwrCtrlOn=1 RTL871X: PowerOnCheck: val_mix:0x0000063f, res:0x0000063f RTL871X: PowerOnCheck: 0x100 the result of cmd52 and cmd53 is the same. RTL871X: PowerOnCheck: 0x1B8 test Pass. RTL871X: Power on ok! RTL871X: rtl8723b_FirmwareDownload fw: FW_NIC, size: 32108 RTL871X: rtl8723b_FirmwareDownload: fw_ver=23 fw_subver=0000 sig=0x5301, Month=03, Date=26, Hour=14, Minute=35 RTL871X: rtl8723b_FirmwareDownload(): Shift for fw header! RTL871X: polling_fwdl_chksum: Checksum report OK! (1, 0ms), REG_MCUFWDL:0x00070305 RTL871X: _8051Reset8723: Finish RTL871X: _FWFreeToGo: Polling FW ready OK! (297, 30ms), REG_MCUFWDL:0x000702c6 RTL871X: FWDL success. write_fw:1, 300ms RTL871X: <=== rtl8723b_FirmwareDownload() RTL871X: HalDetectPwrDownMode(): PDN=0 RTL871X: Set RF Chip ID to RF_6052 and RF type to 3. RTL871X: _init_available_page_threshold(): Enable Tx FIFO Page Threshold H:0x7a7a,N:0x7575,L:0x7575 RTL871X: ===>phy_SwChnl8723B: Channel = 1 RTL871X: pDM_Odm TxPowerTrackControl = 1 RTL871X: ===>phy_SwChnl8723B: Channel = 1 RTL871X: #### hw_var_set_opmode() -5250 iface_type(0) mode = 2 #### RTL871X: Using the default RF gain. RTL871X: MAC Address = 80:a5:89:49:6e:81 RTL871X: start rtl8723bs_xmit_thread(wlan0) RTL871X: rtl8723b_c2h_packet_handler: C2H, ID=9 seq=0 len=7 RTL871X: -871x_drv - drv_open, bup=1 ADDRCONF(NETDEV_UP): wlan0: link is not ready RTL871X: rtl8723b_c2h_packet_handler: C2H, ID=11 seq=1 len=7 RTL871X: rtl8723b_c2h_packet_handler: C2H, ID=11 seq=2 len=7 root@android:/ # RTL871X: rtl8723b_c2h_packet_handler: C2H, ID=11 seq=3 len=7 RTL871X: rtl8723b_c2h_packet_handler: C2H, ID=11 seq=4 len=7 RTL871X: rtl8723b_c2h_packet_handler: C2H, ID=11 seq=5 len=7 RTL871X: rtl8723b_c2h_packet_handler: C2H, ID=11 seq=6 len=7 RTL871X: rtl8723b_c2h_packet_handler: C2H, ID=11 seq=7 len=7 RTL871X: rtl8723b_c2h_packet_handler: C2H, ID=11 seq=8 len=7 RTL871X: rtl8723b_c2h_packet_handler: C2H, ID=11 seq=9 len=7 RTL871X: rtl8723b_c2h_packet_handler: C2H, ID=11 seq=10 len=7 RTL871X: rtl8723b_c2h_packet_handler: C2H, ID=11 seq=11 len=7 RTL871X: rtl8723b_c2h_packet_handler: C2H, ID=11 seq=12 len=7 RTL871X: IsBtDisabled=0, IsBtControlLps=0 RTL871X: ==>rtw_ps_processor .fw_state(8) RTL871X: ==>ips_enter cnts:1 RTL871X: nolinked power save enter RTL871X: ===> rtw_ips_pwr_down................... RTL871X: ====> rtw_ips_dev_unload... RTL871X: rtl8723bs_hal_deinit: issue H2C to FW when entering IPS RTL871X: rtl8723b_set_FwPwrModeInIPS_cmd() RTL871X: rtl8723bs_hal_deinit polling REG_HMETFR=0x4, cnt=1 RTL871X: rtl8723bs_hal_deinit polling REG_HMETFR=0x0, cnt=2 RTL871X: rtl8723bs_hal_deinit: write rpwm=81 RTL871X: rtl8723bs_hal_deinit polling 0x100=0xea, cnt=1 RTL871X: polling done when entering IPS, check result : 0x100=0xea, cnt=1, MAC_1cc=0xea RTL871X: <=== rtw_ips_pwr_down..................... in 70ms root@android:/ # netcfg lo UP 127.0.0.1/8 0x00000049 00:00:00:00:00:00 can0 DOWN 0.0.0.0/0 0x00000080 00:00:00:00:00:00 can1 DOWN 0.0.0.0/0 0x00000080 00:00:00:00:00:00 tunl0 DOWN 0.0.0.0/0 0x00000080 00:00:00:00:00:00 sit0 DOWN 0.0.0.0/0 0x00000080 00:00:00:00:00:00 ip6tnl0 DOWN 0.0.0.0/0 0x00000080 00:00:00:00:00:00 wlan0 UP 0.0.0.0/0 0x00001043 80:a5:89:49:6e:81
版权声明：本文内容由互联网用户自发贡献，该文观点仅代表作者本人。本站仅提供信息存储空间服务，不拥有所有权，不承担相关法律责任。如发现本站有涉嫌侵权/违法违规的内容， 请发送邮件至 举报，一经查实，本站将立刻删除。
发布者：全栈程序员-用户IM，转载请注明出处：https://javaforall.cn/108967.html原文链接：https://javaforall.cn
【正版授权，激活自己账号】： Jetbrains全家桶Ide使用，1年售后保障，每天仅需1毛
【官方授权 正版激活】： 官方授权 正版激活 支持Jetbrains家族下所有IDE 使用个人JB账号...
